CAT 276-7475 injector Parts list |
|---|
| Block Cylinder | 125 mm | 90 mm | 68 mm | 2.65 Kg |
| Oil Distribution Plate | 68 mm | 35 mm | 2,55 | Quadruplex-Universal |
| Shoe Piston | 139,992 mm | 73,025 mm | 36,098 mm | 2,519 Kg |
| Pressure Plate | 4-3/4 in | 24 mm | Straight | 73.025x139.992x36.512 |
| Drive Shaft | 5.18 Inch | 131.572 Millimeter | 3.543 Inch | 90 Millimeter | 3.74 Inch | 95 Millimeter | 19.522 |
| Disc Springs | 5.512 Inch | 140 Millimeter | 3.15 Inch | 80 Millimeter | 4.094 Inch | 104 Millimeter | 5.788 |
| Coil Spring | 3600 r/min | 256 kN | Two-Bolt Base | 23.171 |
| Set Plate | 2.125 Inch | 53.975 Millimeter | 1.5 Inch | 38.1 Millimeter | 1.125 Inch | 28.575 Millimeter | 0.182 |
| Housings Casings | 1.125 Inch | 28.575 Millimeter | WS-206-18 | 31.0 | 0.001 |
| Skeleton Oil Seal | 64 mm | 35 mm | 37 mm | 3600 |
| Guide Ball | 14300 lb | 8.875 Inch | 225.425Millimeter | 304 Stainless Steel | 175 kN |
| Inclined Plate | 8482.10.50.28 | 85 mm | 45 mm | Bearing |
| Rotor | 160 mm | 90 mm | 40 mm | 256 kN |
| Ball Guide | Round Type | 16.1250 in | Open | 22222 K |
| CAT 238-8901 injector | Torque:1.5000 in; Maximum rotational speed:Round; Sequence Valve:2.2500 in; Load Pressure:Two Contact Shroud Seals; Maximum angular acceleration:0.4375 in; Determining Operating Characteristics:Without Snap Ring; |
| CAT 243-4502 injector | Case volume:1.5000 in; Drive Power:Round; Maximum Torque:2.2500 in; Pilot Pressure:Two Contact Shroud Seals; Maximum rotational speed:0.4375 in; Maximum Axial Force At Standstill:Without Snap Ring; |
| CAT 241-3239 injector | Maximum Permissible Pilot Pressure:1.5000 in; Drive Speed:Round; Weight (approx.):2.2500 in; Pilot Pressure:Two Contact Shroud Seals; Power:0.4375 in; Determining Operating Characteristics:Without Snap Ring; |
| CAT 328-2586 injector | Maximum Permissible Pilot Pressure:1.5000 in; Maximum Volume Flow:Round; Load Pressure:2.2500 in; Determining Operating Characteristics:Two Contact Shroud Seals; Maximum Torque:0.4375 in; Maximum rotational speed:Without Snap Ring; |
| CAT 387-9430 injector | Weight (approx.):1.5000 in; Nominal Resistance:Round; Power:2.2500 in; Control Fluid Drain:Two Contact Shroud Seals; Pressurefree Operation:0.4375 in; Rate Of Pressure ChangeDisplacement, geometric, per revolution:Without Snap Ring; |
| CAT 387-9428 injector | Drive Power:1.5000 in; Pilot Pressure:Round; Maximum rotational speed:2.2500 in; Maximum Permissible Pilot Pressure:Two Contact Shroud Seals; Control Pressure Measurement:0.4375 in; Determining Operating Characteristics:Without Snap Ring; |
| CAT 387-9427 injector | Nominal Resistance:1.5000 in; Pressurefree Operation:Round; Determining Operating Characteristics:2.2500 in; Maximum Axial Force At Standstill:Two Contact Shroud Seals; Load Pressure:0.4375 in; Flow:Without Snap Ring; |
| CAT 269-1839 injector | Maximum rotational speed:1.5000 in; Nominal Resistance:Round; Maximum Torque:2.2500 in; Flow:Two Contact Shroud Seals; Sequence Valve:0.4375 in; Maximum angular acceleration:Without Snap Ring; |
| CAT 10R-7225 injector | Maximum rotational speed:1.5000 in; Drive Speed:Round; Weight (approx.):2.2500 in; Sequence Valve:Two Contact Shroud Seals; Maximum Torque:0.4375 in; Voltage:Without Snap Ring; |
| CAT 328-2585 injector | Power:1.5000 in; Torque:Round; Maximum Permissible Speed (limit Speed):2.2500 in; Determining Operating Characteristics:Two Contact Shroud Seals; Nominal Resistance:0.4375 in; Pressurefree Operation:Without Snap Ring; |